There are a few affiliate links in this post (marked with a *) so if you shop via my link I may earn a small commission. This is of no extra cost to you, but helps support this blog!
This tutorial is for making a card using an aperture card (a card which has a hole cut out already for you). If you have a normal, blank card you can cut out your own square in the middle; the size of the one I show you here is 6cm x 6cm.
You will need:
- A blank card (a tri-fold aperture card works best and I used this pack from Amazon*)
- A piece of aida (I recommend this Antique White Aida from Love Crafts*)
- A pattern that will fit your card (I have some you can download for free below)
- A piece of felt if you have a double-fold card
- A needle
- Embroidery floss (I recommend DMC which you can get from Love Crafts here* and they stock the glitter threads)
- Double-sided tape
- A warm drink and snack (optional, but definitely makes this more even more fun)!
7 Steps to Make a Cross Stitch Christmas Card
1. Stitch your design
Cut your aida at least 2cm bigger than the hole on the card. If you are using the same cards as me then 8x8cm is the minimum but you might want it a little bigger while you are stitching to make it easier.
Then stitch your design onto the centre of your
You will be using quite a small piece of
2. Cut your aida and
If you cut your aida a little big while stitching now you need to cut it to size (so 8x8cm for a 6x6cm hole). You want it to be bigger than the width and height of the square that’s cut out, but smaller than the width and height of the whole card. And remember to keep your design centre before you cut it.
Next, you may need to cut out some felt if you have a double-fold card. If you have a tri-fold card you can skip ahead to step three.
3. Stick on the tape
Now it’s time to stick on the
You will need two 7.5cm strips and two 5.5cm strips, and they all should be between 0.5-1cm thick.
Stick your longer strips on the top and bottom of the square on the inside of the card. Get the strips as close to the edge as possible without them showing through on the front. Then repeat with the two shorter strips at either side.
4. Check it fits
Put your stitched design right side down on the inside of the card in the square and have a quick check of what your design will look like at the front. Make sure it is
5. Stick it onto the card
Lift up one side of the aida, trying not to shift the piece too much and peel off the top layer of the tape. Once you are sure it is lined up correctly stick this side down.
Check at the front again to make sure it is still centre and fix it if you need to (it’s much easier to fix when only one side is stuck down).
After checking, peel off and stick down the other 3 edges. The next step is for double-fold cards if you have a tri-fold card you can skip to step seven.
6. Stick on the felt
Next, it’s time to stick on the felt to cover up the stitches at the back.
Cut out another 4 strips of tape, the same length and thickness as before (two 7.5cm x 0.5-1cm and two 5.5cm x 0.5-1cm). Stick them on the
Peel off the strips and stick on the felt.
Your card is now finished! The next step is for tri-fold cards so you can scroll down for a little more information.
7. Stick the fold down
It’s now time to stick two sides of the card together to cover up the back of your stitching.
Please note, mine has felt on as I am showing you two ways of making the card. You don’t need to put felt on if you have a tri-fold card, but you still can if you would like to.
Stick four strips of double-sided tape onto the left-hand side of your card. You can also put the tape in the middle part of the card, but I like to do it this way so I can’t accidentally stick the wrong two sides together (talking from experience).
You will need two 17 cm strips and two 9 cm strips and they need to be around 1 cm thick.
Peel off the tops of the tape and gently fold the card over on top of the tape.
Press down on the card to stick both sides together and you should be left with a double-fold card and no stitching visible on the inside.
Now you just need to fill them with words for your loved ones.
If you are stuck on any of the parts of this tutorial please just get in touch (email@example.com) or come and join over 2000 fellow stitchers in my Facebook group!
5 thoughts on “How To Make A Cross Stitch Christmas Card (With Free Christmas Cross Stitch Patterns)”
this was very very helpful. Thank you for the pictures and guide.
You’re welcome Dawn, glad you found it helpful!
What size Aida did you use? 14?
Hi Elaine, Yes, Hannah did use 14ct Aida. 🙂
This is so cute Hannah!